top of page

Tarmac Sealing in Barlestone – Pressure Washing Job Analysis

Nov 2
7 min read

Tarmac Sealing can completely transform the appearance of an ageing driveway, but getting a great finish isn't simply a case of applying sealer to the surface.

A recent Tarmac Sealing job in Barlestone demonstrated exactly why preparation, the right pressure washing equipment and adapting your approach to the condition of the driveway are so important.

This particular driveway had a number of challenges to deal with before it was ready for sealing. The property had recently had building work carried out, leaving mortar on sections of the tarmac, while moss and weeds had established themselves around the edging blocks.

The aim was simple: clean the driveway thoroughly, remove the contamination without damaging the tarmac and then apply two coats of sealer to bring the surface back to a deep black finish.


tarmac sealing on a driveway
Before and after Tarmac Sealer was applied to a driveway in Barlestone

Pressure Washing The Driveway Before Tarmac Sealing


When I arrived at the Barlestone property, the driveway had recently been affected by building work.

The builders had left some mortar on the tarmac, including an area where material had apparently been deposited while waste was being put into the skip. There was also mortar around the side section and even some material that had made its way into the drain.

That immediately created a potential problem.

The concern wasn't simply getting the mortar off. It needed to be removed without damaging the tarmac underneath it.

There was also plenty of moss and weeds to deal with, particularly around the edging blocks.

The tarmac itself had a noticeably grey appearance when dry, rather than the deep black finish that we wanted to achieve after the sealing process.


Pressure Washing To Remove Moss and Weeds


Before the Tarmac Sealing could begin, the driveway needed to be properly cleaned.

One of the noticeable differences with this driveway compared with some previous Tarmac Sealing jobs was the amount of moss and weeds around the edging blocks.

There was quite a lot of moss further up the driveway, while weeds were growing out from between the blocks around the edges.

A pressure washer was used to remove as much of this contamination as possible.

For the tarmac itself, the first choice was a surface cleaner.


Why Use a Surface Cleaner on Tarmac?

When pressure washing tarmac, it's important to consider the condition of the surface and avoid using unnecessarily aggressive techniques.

A surface cleaner allows the pressure to be distributed more evenly across the surface. For this job, it was the preferred method for cleaning as much of the tarmac as possible while reducing the risk of damaging the surface.

A turbo nozzle was deliberately avoided on the tarmac.

Turbo nozzles are extremely useful for certain cleaning applications, and they were used on the edging blocks to help remove the weeds. However, using one directly on the tarmac can start to remove some of the surfacing.

That wasn't something we wanted to happen.

The objective of this Tarmac Sealing job was to keep the existing tarmac intact and maintain an even texture across the driveway.

a surface cleaner for pressure washing on a tarmac driveway before tarmac sealing
Using a surface cleaner on Tarmac to gently clean the surface when pressure washing

The Mortar on the Tarmac


The biggest challenge of this job was the mortar that had been left on the driveway following the building work.

Initially, there was some concern that removing it could affect the texture of the tarmac.

The first attempt with the surface cleaner didn't remove the mortar, so another approach was needed.

A fan jet was then used to tackle the affected area.

Thankfully, this worked.

Some sections required the pressure to be brought closer to the mortar to remove it, but it ultimately came away without creating a noticeable difference in the texture of the tarmac.

Before working on the tarmac, the approach was also tested on the metal around the drain. This helped establish how the material was going to respond before continuing.

The result was exactly what was wanted: the mortar was removed while keeping damage to the tarmac to a minimum.

There was no need to resort to acid treatment.

That was particularly important because using acid would have introduced another stage to the process, requiring the area to be thoroughly diluted and rinsed afterwards to avoid damaging the tarmac.


Cleaning Up After Pressure Washing


Once the main cleaning was complete, there was still some manual work required.

Not every weed had been removed by the pressure washer, so the remaining weeds around the blocks were taken out manually.

The windows also needed attention.

Because the turbo nozzle had been used close to the windows while cleaning the edging blocks, they had become splattered during the cleaning process.

As the customer was a regular customer who normally has their windows cleaned using a water-fed pole, the decision was made to clean them traditionally on this occasion.

The reason was simple: there was no desire to get the newly cleaned tarmac wet again before sealing it.

Once everything was finished, the driveway was ready for the next stage.

The tarmac was clean and ready for sealer.


Applying the First Coat of Tarmac Sealer


With the cleaning completed, it was time to start the Tarmac Sealing process.

The first coat was applied across the driveway.

The purpose of the first coat isn't necessarily to make the driveway look perfect immediately.

Instead, the first coat needs to soak into the tarmac.

The sealer used on this job is relatively thick compared with many domestic tarmac sealers. This also meant that the surface didn't need to be completely dry before application, provided there wasn't any standing water.

Then came an unexpected challenge.

The Rain Arrives!

Just as the first coat had been completed, the heavens opened.

It was raining heavily shortly after the first coat was applied.

Fortunately, this wasn't necessarily a disaster.

The first coat had already been applied and the objective was for it to soak into the tarmac. There was no significant runoff, and the sealer had behaved as expected.

The weather forecast was also favourable, with warmer and sunnier conditions expected later in the afternoon.

So the job was left to allow enough time for the first coat to dry before returning for the second.


The Second Coat


After the first coat, the driveway looked somewhat patchy. However, this was expected because the first coat had been absorbed into the tarmac.

Once the second coat was applied, the colour became much deeper and more uniform.

For the large main section of the driveway, the sealer was worked in the opposite direction from the first coat where possible.

This helps get into different divots and textured sections of the tarmac from another angle and can help ensure more consistent coverage.


Why You Don't Want Too Much Sealer on the Surface


One of the important parts of applying Tarmac Sealing isn't just putting enough product down.

It's also about controlling how much sealer remains on the surface.

The aim was to get enough sealer onto the driveway to colour it, protect it and fill the gaps within the surface texture, but without leaving an unnecessarily thick layer sitting on top.

The roller was therefore extended over a larger area to help distribute the sealer and remove excess from the surface.

This helped keep the finish uniform across the driveway.

The goal wasn't to completely flatten the existing texture.

Instead, the intention was to maintain the natural texture of the tarmac while bringing the colour back to a deep black.


The Finished Tarmac Sealing Result


By the end of the second coat, the transformation was clear.

The grey-looking tarmac had been brought back to a deep black finish, while the texture of the existing surface remained visible.

The mortar had been successfully removed, the moss and weeds had been dealt with and the driveway had been given its two coats of sealer.

Most importantly, the concerns about creating a different texture where the mortar had been were avoided.

The end result was exactly what the job required.

And the customers were really happy with the finished driveway.


What This Barlestone Job Shows About Tarmac Sealing


This job is a good example of why Tarmac Sealing isn't simply about rolling sealer onto a driveway.

The preparation beforehand can make a huge difference.

In this case, the driveway had:

  • Mortar left behind from building work

  • Moss around the edging blocks

  • Weeds growing between the blocks

  • Dirt and grime embedded into the tarmac

  • A faded grey appearance

Each problem required a slightly different approach.

The tarmac was cleaned with a surface cleaner, the edging blocks were treated more aggressively where appropriate, the mortar was removed using a fan jet and the remaining weeds were removed manually.

Only once the driveway was properly prepared was it ready for the two coats of sealer.


Why Consider Tarmac Sealing?


If your tarmac driveway has started to look faded and tired, Tarmac Sealing can be an effective way of refreshing its appearance.

Rather than immediately replacing an existing driveway, sealing can give suitable tarmac a new lease of life.

The process can:

  • Restore a much darker appearance

  • Help protect the existing tarmac

  • Improve the overall kerb appeal of the property

  • Give an ageing driveway a more refreshed appearance

  • Extend the useful life of a suitable existing surface

However, the condition of the driveway needs to be considered before sealing. Tarmac Sealing isn't designed to fix every structural problem, so assessing the existing surface is an important part of the process.


Tarmac Sealing in Barlestone


This Tarmac Sealing in Barlestone job was a great example of how much preparation can go into what might initially look like a straightforward driveway sealing job.

From removing weeds and moss to tackling stubborn mortar left behind by building work, the driveway needed to be carefully prepared before the sealer could be applied.

The unexpected rain after the first coat provided another challenge, but because the first coat had already soaked into the tarmac and there was no problematic runoff, the job could continue once the weather improved.

The second coat then brought the driveway back to the deep black appearance we were looking for.

The customers were delighted with the finished result.


Looking for Tarmac Sealing?


If your tarmac driveway is looking faded, grey or generally past its best, Wilkinson Property Pro provides professional Tarmac Sealing designed to refresh and protect suitable existing tarmac surfaces.

Our process involves thoroughly preparing the surface before applying two coats of sealer to achieve a consistent, long-lasting finish.

If you're considering Tarmac Sealing in Barlestone or the surrounding area, get in touch with Wilkinson Property Pro to discuss your driveway and find out whether Tarmac Sealing could be suitable for your property.

Comments


bottom of page